New Optus SMS Gateway Number | The Latest Australian Technology

Optus SMS

It is a bit tricky to install the Optus SMS Gateway without the help of a professional. The installation instructions are quite vague and sometimes it’s necessary to rewire your sockets. Despite this, you can still use it to make calls. It’s worth having a second cordless phone in your spare bedroom or kitchen. Fortunately, Optus will waive the cost of professional installation when you purchase the Gateway.

Ethernet Cable

You need to connect an Ethernet cable to the port marked WAN. You need to connect a cable from your connection box to the WAN port of your modem. Then, you need to plug the other end of the cable into the LAN port. After connecting the Optus Gateway, you need to connect the Ethernet cable to the LAN port. Then, connect the power cord to the ‘DS’ port.

Optus Connection Box

The Optus SMS connection box has green lights for the Upstream (US) and Downstream (DS) ports. Make sure the DS light is lit. If the US light is on, you must connect your Ethernet cable to the WAN port. Ensure that both of these lights are steady. Once you have successfully connected your Optus connection box, you can test your WiFi connection by downloading the Optus @Home app.


To update the firmware, go to the settings page on the Optus SMS gateway. It will automatically push a new version of the firmware to your device. The LAN light indicates that you’re connected to your modem router. If it isn’t, you can remove the cover and install the latest version. The WAN light will indicate your connection to the modem router. The DS light will indicate that you’re connected to the Internet. The Upstream (US) signal will be visible if the connection is stable.

Home Telephone

After installing your Optus SMS Gateway, you must first connect it to your NBN network. Connect the Ethernet cable to the WAN port and also then plug the connection box into the DS port. Once you’ve connected your router, you’ll need to plug the home phone into the NBN network. To install the Optus gateway, you must configure the NBN modem. Once you’ve done that, you’ll need to plug in your home telephone.

When you’re installing the Optus SMS Gateway, make sure the Modem is connected to the Ethernet port. Then, plug the Ethernet cable into the WAN port. If your connection is stable, you can begin using your new service. After a couple of days, you’ll be able to do almost anything on the internet. You can even download apps and games that you have downloaded. You can also use the Optus Gateway to connect to your mobile phone.

Internet Connection

Once you’ve connected your modem to the LAN port, you should check your Optus SMS Gateway’s Internet light. If it’s not, you’ll need to make sure your internet connection is connected to the modem router. The lights on your modem are flashing, your internet connection is not working. If your connection isn’t, contact Optus technical support. However, if you have a bad connection, it’s likely a faulty device.

When you’ve finished installing the Optus Gateway, you should check the lights on the Connection Box. The LAN light indicates the connection to your modem router. If the WAN light is solid green, you’re connected to the network. The WAN light shows that you’re connected to the modem router. The green WAN light indicates that you’re connected to the internet. The red WAN light means that your connection is weak and also the device is disconnected.

NBN Protocol

The Optus Gateway is a modem that connects to the Internet. It uses the NBN protocol to connect to the Internet. It has three ports: LAN, WAN, and also LAN. If you have a connection to the NBN, you’ll need to connect the Optus Connection Box Ethernet cable to the WAN port. The WAN port is the same as the LAN port, but it will have two more functions.


The IP address is the same for all the devices connected to the network. If the IP address does not match up, you can try to enter the IP address in the IP address field to get your router connected. Once you’ve entered the IP address, it will start the configuration process. The IP address is used to identify the network, and the username and also password are used to connect the devices. The default login information for an Optus Gateway is listed on the router’s manual.


No comments yet. Why don’t you start the discussion?

Leave a Reply

Your email address will not be published. Required fields are marked *